Accessories

For over fifty years Dieco has been the go-to for all your spring, tool and die accessories. We work with many specialized companies, so no matter what you need we can find the right product.

die makers grease

  • Lithium Complex
  • Fortified with extreme pressure additives, excellent for close tolerance, high unit pressure applications
  • Dropping point of 500 degrees Fahrenheit, freeze point of 10 degrees Fahrenheit
  • Rust and oxidation inhibitors added
  • Ideal for use with Die Sets on Pins and Bushings
  • Dieco Die-makers Grease SDS
  • Formerly DIECO Linear Lube
  • Same product, new package
  • Designed for use on ball bearing assemblies
  • Blend of the finest quality pure synthetic oils available
  • USDA H-1 rated. Full acceptability for use in all areas where incidental food contact may occur

dieco pry bars

  • PRY BARS made of hexagonal high carbon steel stock, hot forged to shape and cadmium plated
  • Weighs only 1 ¾ lbs. with an overall length of 18 ¾
  • BRONZE TIPS available to fit on curve ends of pry bars and are removable

ostalloy

  • Fusible Alloys are low melting temperature compositions containing bismuth, lead, tin, cadmium, or indium
  • Only expands approximately 3.3% of their volume when changing from molten to solid form
  • Advantage of fusible alloys is their capacity for recovery
  • Can be remelted and used again and again
  • Ideal for many industrial applications including casting, tube bending, machining parts for soft metal dies, fixturing, soft metal casting, joggle dies and supporting castings and interrupted cuts
  • Sold in 1-pound increments

DAC

  • DAC Industries innovative selection of “problem solving” injection molding maintenance products will improve your product quality, reduce production cost, and increase profitability!
  • DAC mold release products, cleaners, degreasers, lubricants and rust inhibitors are designed to do away with rejected parts due to “marking and contamination”, which are most commonly caused by “leeching and bleeding”… a direct result of ineffective machine maintenance.
  • Choose from an extensive variety of specialty products that have been designed to extend machine and tool life, improve mold release properties, and increase efficiency

urethane products

  • Cylinder / Tubes
  • Closed-End Punch Strippers
  • Urethane Springs
  • Rods
  • Pads
  • Poly-Hammers

carrlane

  • Alignment Pins
    • L & T Pins
    • Clamping Pins
    • Slotted Locator Bushings
    • Ball Lock Pins & Mounting Systems
    • Detent Pins & Expanding Pins
    • Cable
  • Hoist Rings
    • Fluted Knobs
    • Four-Prong Knobs & Screw Clamps
    • Adjustable Handles and Knob Handles
    • Knurled Knobs & Screw Clamps
    • Socket-Head Screw Clamps
    • Bar-Handle Screw Clamps
    • Hand Wheels & Latch Screws
  • Spring-Loaded Devices
    • Hand Retractable Plungers
    • Ball Plungers & Spring Plungers
    • Spring Locating Pins
    • Spring Stop Buttons
  • Supports, Resets, & Feet
    • Leveling Feet
    • Swivel Pads & Grippers
    • Rest Buttons & Pads
    • Screw Jacks
  • Locators
    • Construction Balls
    • Fixture Keys
    • Locating Pins
  • Clamps & Accessories
    • Portable Clamps & Hand Tools
    • Nuts & Washers
    • Studs, Bolts, & Clamping Accessories
    • Clamping Kits & Clamp Straps
    • Edge Clamps & Swing Clamps
  • Plug Gages, Threaded Inserts, Jig & Fixture Bases
    • Blank Tooling Plates * Blocks
    • Angle Brackets
    • Cast Sections
    • Adjustable Lockign Hubs
  • Chuck Jaws
  • Modular Fixturing
  • Toggling Clamps
  • Press Fit Bushings
    • Designated as Type P, these bushings are the least expensive and most popular bushings. Generally used in single step drilling. Pressed flush in the fixture plate, they can be spaced closer together than other types of bushings. Available as unground with additional outside diameter stock.
  • Head Press Fit Bushings
    • Designated as Type H, these bushings can accept heavier axial loads than type P bushings whether mounted with the head above the fixture or recessed into the fixture. Also available as unground with additional outside diameter stock.
  • Slip/Fixed Renewable Bushings
    • Designated as Type SF or SFX, these bushings are mostly used when the number of holes drilled will be greater than expected life of the bushing. Type SF and SFX bushings are also used when a hole is drilled, then a reaming or tapping operation is required. By slipping the bushing out of the liner another size may be installed for the next operation to be performed. Clamps or lock screws are used to secure them in the fixture.
  • Fixed Renewable Bushings
    • Designated as Type FM, these bushings are mostly used when the number of holes drilled will be greater than the expected life of the bushing. By slipping the bushing out of the liner another size may be installed for the next operation to be performed. Clamps or lock screws are used to secure them in the fixture.
  • Lamina Flat & Other Products
    • L-Gibs, V-Gibs, Square Gibs
    • Gib Assemblies
    • Guide Blocks
    • Keeper Blocks
    • Wear Plate
    • Wear Strips
    • Stock Lifters
    • Pad Retainers
    • Mold Pins & Bushings
    • Marsh Mellow Springs
    • Hydraulics
    • Cam Units
    • Ball Bearing Scrub
  • Drill Rods
    • It is used extensively in dies and punches for blanking, forming and trimming, as well as in cams, bushings, guides and gauges
  • D-2 Tool Steel
    • Heat treat temperature 1600-1650 F
    • Quench Air or Oil
    • Hardness Rockwell 60c-62c
    • Applications D2 has high wear resistance, good toughness, and low distortion. It is often chosen when long tool life is required
  • Steel Shim Stock
    • Low carbon mild steel cold rolled to a #1 hard temper.
    • Stiff and springy, and can be used where hardness is required
    • Can be punched or sheared with minimum burring and distortion
    • Meets the following specifications: AISI 1010 and QQS 698
  • Spring Cages
    • Cold rolled steel
    • Cages are case hardened by carbonitriding
  • Eagle Screw Caps
    • Eagle Screw Caps are easy to use
    • Saves time in basic die assembly, disassembly, and maintenance operations
    • Ideal in long run dies where maintenance is crucial and on-going
  • Amcor
    • Adjustable stock lifters
    • Automatic stops
    • Die stop pins
    • Gripper buttons
    • Pad retainers & plunger pins

  • Unipunch
    • Rugged, heavy duty units for multiple hole punching and notching
    • Offers a wide range of standard holder widths, throat depths, and round and shaped Punches and Dies.
    • Punch heads and bodies are separate, which lets you quickly change hole size and shape, simply by changing the inexpensive Punch bodies.
    • Reuse the Punch Heads indefinitely. Low-cost Die Buttons complete the Punch system and offer close tolerances for accuracy and interchangeability
  • Argon
    • Standard Steel Stamps & Holders Used for Automotive & Stamping Industry standard marking devices
    • Branding & Stamping Tools

  • Ball Lock Mounting Systems
  • Locating Components
  • Gripper Products
  • Workholding Components
  • Vises & Accessories
  • Kwik Lock Pins
  • Power Clamping

  • Reid Supply
    • Tooling Components
      • Bolts, Studs & T-Nuts, Shim Stock, CMM Fixturing, Jig & Fixture Blocks & Plates, Locating Tools, Mold Components, Nuts, Pallet Fixtures Rest Buttons, Pads & Supports, Spring-Loaded Devices, Washers
    • Clamps& Workholding
      • Clamps, Fixturing Components, Hydraulic Clamps & Workholding, Pneumatic Clamps & Workholding, Vises & Milling Machine Accessories
    • Leveling Devices & Vibration Control
      • Leveling Pads, Machinery Levelign Mounts, Vibration Mounts
    • Knobs, Handles & Hand Wheels
      • Handles, Hand Wheels, Knobs, Levers
    • Fasteners & Hardware
      • Fasteners, Hardware, Quick Release Pins & Accessories, Thread Inserts & Accessories
    • Bearings & Power Transmission
    • Cable Ties & Accessories
    • Material Handling
    • Metalworking
    • Tools, Maintenance & Shop Supplies • Pneumatics & Hydraulics • Structural Systems • Safety • Packaging & Shipping Supplies
  • Ball Lock Punches & Retainer Sets
  • Standard Line Wire EDM Blanks
  • Standard Line Punches
  • Custom Specials, OEM Components, Injection Mold Components – Visit Ring Precision